AVR 18 (serv.man7) - Harman Kardon Audio User Guide / Operation Manual. Page 21

Read Harman Kardon AVR 18 (serv.man7) User Guide / Operation Manual online

19
ENGLISH
Operation
Basic Operation
Once you have completed the setup and
configuration of your new receiver, it is
simple to operate and enjoy. The following
instructions will provide the steps needed
to enjoy the AVR18 RDS:
• When using the AVR18 RDS for the first
time, it is necessary to press the 
Main
Power
button 
1
on the front panel to
turn the unit on. This places the unit in a
standby mode, as indicated by the amber
color of the 
Power Indicator
3
. Once
the unit is in standby, you may begin a
listening session by pressing the 
System
Power Control
2
on the front panel or
the 
Main Power On
button 
å
on the
remote. Note that the 
Power Indicator
3
will turn red, then green. This will turn
the unit on and return it to the input
source that was last used. The unit may
also be turned on from standby by pressing
any of the 
Input Selector
buttons on the
front panel 
! #
.
To turn the unit off at the end of a
listening session simply press the 
System
Power Control
2
on the front panel or
the 
Main Power Off
button 
on the
remote. Power to any equipment plugged
into the rear panel 
Switched AC Outlet
will be shut off and the 
Power
Indicator
3
will turn amber.
When the remote is used to turn the unit
“off” it is actually placing the system in a
standby mode, as indicated by the amber
color of the 
Power Indicator
3
.
When you will be away from home for an
extended period of time it is always a good
idea to completely turn the unit off using
the front panel 
Main Power Switch
1
.
Note that all preset memories may be lost
if the unit is left turned off completely for
more than two weeks.
• To dim the brightness of the front panel
display, press the 
Dimmer
button 
˙
on
the remote. The first press will dim the
lights to half normal. A second press will
turn the display completely off. Press the
Dimmer
button 
˙
again to restore the
display to normal brightness.
Source Selection
• To select a source at any time, press any
of the 
Source Selector
buttons on the
remote 
ç∂
or front panel 
! @ #
.
• The front panel 
Video 3 Inputs
)
may be used to connect a device such as a
video game or camcorder to your home
entertainment system on a temporary
basis.
• When a pure audio source is selected
(Tuner, CD, Tape, Phono, 6 channel direct
inputs) the last video input used (DVD;
Video 1/2/3) remains routed to the 
Video
1 Outputs
and 
TV Monitor Output
. This permits simultaneous viewing
and listening to different sources.
• During a listening session you may wish
to adjust the 
Bass
7
and 
Treble
8
controls to suit your listening tastes. Note
that these controls are not effective when
the 6 channel direct inputs are selected.
• To temporarily silence all speaker and
preamp outputs press the 
Mute
button 
¬
Ò
. This will cut the output but it will not
effect any recording or dubbing that may
be in progress. When the system is muted
the 
MUTE
indicator will light in the
Information Display
¯
. Press the
Mute
button 
¬ Ò
again to return to
normal operation.
• For private listening, plug the 6,3 mm
stereo phone plug from a pair of stereo
headphones into the front panel
Headphone
jack 
4
.
• To turn the speakers off for private
listening, press the 
Speakers Off
button
6
.
• When a Video Input source is selected
the video signal for that input will be
routed to the 
TV Monitor Video
Output
jack 
and will be viewable on a
TV monitor connected to the AVR18 RDS.
Make certain that your TV is set to the
proper input to view the signal. 
• To program the AVR18 RDS for
automatic turn off, press the 
Sleep
button
©
on the remote. Each press of the button
will increase the time before shut down in
the following sequence:
The sleep time will be displayed in the
Information Display and it will count
down until the time has elapsed.
When the programmed time has elapsed
the unit will automatically turn off (to
Standby mode). Note that the front panel
display will dim to one half brightness
when the Sleep function is programmed.
To cancel the Sleep function, press the
Sleep
button 
©
until the Sleep indicator
numbers disappear and the Information
Display shows the current source. Pressing
any control button while the Sleep control
is activated will momentarily return the
Information Display to full brightness for
increased legibility without interrupting
the Sleep function.
90
min
80
min
70
min
60
min
50
min
40
min
30
min
20
min
10
min
OFF
Page of 30
Display

Click on the first or last page to see other AVR 18 (serv.man7) service manuals if exist.