KP-51WS510, KP-57WS510, KP-65WS510 - Sony TV Service Manual (repair manual). Page 17

Read Sony KP-51WS510 / KP-57WS510 / KP-65WS510 Service Manual online

— 17 —
KP-51WS510/57WS510/65WS510
2-6.  2-POLE MAGNET AND CENTERING 
MAGNET ADJUSTMENT
1.  Set the picture mode to PRO and picture to MAX.
2.  Either select the PJED Test Pattern dot hatch signal or apply an 
external dot signal.
3.  Cover the red and blue CRT lenses with lens caps to allow only green 
to show (or use the method shown in the note below for turning off 
the CRTs individually without using lens caps).
4.  Turn the focus VR on the focus block to the left (counter clockwise) 
and set it to overfocus to enlarge the spot.  
5.  Adjust the CRT’s 2-pole magnet so that the small bright spot is in the 
center.
6.  Align the focus VR on the focus block and set it for the best focus.
7.  Apply a Monoscope signal to the set.
8.  Adjust the H-CENTERING and V-CENTERING roughly by the 
centering magnets.
9.  Check 2-pole magnet adjustment. If necessary repeat steps 1-6.
10. Repeat steps 1 through 9 for the red CRT covering the green and 
blue CRT lenses with lens caps to allow only red to show (or use the 
method shown in the note below for turning off the CRTs individually 
without using lens caps) and adjust the red focus control on the focus 
block.
11. Repeat steps 1 through 9 for the blue CRT covering the red and 
green CRT lenses with lens caps to allow only blue to show (or 
use the method shown in the note below for turning off the CRTs 
individually without using lens caps) and adjust the blue focus control 
on the focus block.
Note: If lens caps are unavailable, you can cut off the unnecessary color 
beams by controlling the service mode 2150P-2 1 RGBS.
2-7.  CENTERING MAGNET ADJUSTMENT
  Not required - Combined with 2-6 2-Pole And Centering Magnet 
Adjustment.
2-8.  4-POLE MAGNET ADJUSTMENT
1.  Set the picture mode to PRO and picture to MAX.
2.  Receive the Dot signal.
3.  Cover the red and blue CRT lenses with lens caps to allow only green 
to show (or use the method shown in the note below for turning off 
the CRTs individually without using lens caps).
4.  Turn the (green) focus VR on the focus block to the right (clockwise) 
and set it to under-focus to reduce the spot.
5.  Adjust the 4-pole magnet so that the small spot in the center of the 
screen becomes round for green and red.
6.  Adjust the blue spot to an oval shape X:Y=1:1.2
Note: If lens caps are unavailable, you can cut off the unnecessary color 
beams by controlling the service mode 2150P-2 1 RGBS.
��������������������
������������������������
������������������
2-9.  BLUE DEFOCUS ADJUSTMENT
1.  Setup: Apply a Dot Hatch Signal and set the mode to Pro Mode. 
Change the color temperature to Cool in the user’s menu.
2.  Cover the red and green CRT lenses with lens caps to allow only blue 
to show (or use the method shown in the note below for turning off 
the CRTs individually without using lens caps).
4.  Turn the blue focus VR on the focus block to the right (clockwise) to 
make the round dot oval. 
D1
Blue
D1:D2 = 1:1.2
D2
5.  Check the flare with a high luminance signal to make sure the flare is 
minimal while the bright spot is located in the center, If not, readjust 
the 2 and 4-pole magnets.
6.  Check for uniformity on a 100% IRE to an all white signal.
Note: If lens caps are unavailable, you can cut off the unnecessary color 
beams by controlling the service mode 2150P-2 1 RGBS.
Page of 127
Display

Click on the first or last page to see other KP-51WS510 / KP-57WS510 / KP-65WS510 service manuals if exist.