Read Sony CDX-GT560UE / CDX-GT560UI / CDX-GT560US / CDX-GT564UI / CDX-GT610UG / CDX-GT610US / CDX-GT616UG / CDX-GT61UMS Service Manual online
CDX-GT61UMS/GT560UE/GT560UI/GT560US/GT564UI/GT610UG/GT610US/GT616UG
5
NOTE FOR REPLACEMENT OF THE USB CONNEC-
TOR (CN902) AND THE AUX JACK (J901)
To replace the USB connector and the AUX jack requires align-
ment.
1. Insert the USB connector and the AUX jack into the front pan-
TOR (CN902) AND THE AUX JACK (J901)
To replace the USB connector and the AUX jack requires align-
ment.
1. Insert the USB connector and the AUX jack into the front pan-
el.
2. Place the KEY board on the front panel and align the terminals
of the USB connector and the AUX jack with the holes in the
KEY board.
KEY board.
3. Solder seven terminals of the connector and three terminals of
the jack.
SERVO board
(CN401)
(CN401)
MAIN board
(CN700)
(CN700)
extension cable (CD mecha)
KEY board
front panel
USB (socket) connector
AUX jack
TEST DISCS
Use following TEST DISC when this unit confi rms the operation
and checks it.
Use following TEST DISC when this unit confi rms the operation
and checks it.
Part No.
Description
3-702-101-01
DISC (YEDS-18), TEST (for CD)
4-225-203-01
DISC (PATD-012), TEST (for CD)
NOTE FOR REPLACEMENT OF THE SERVO BOARD
When repairing, the complete SERVO board should be replaced
since any parts in the SERVO board cannot be repaired.
When repairing, the complete SERVO board should be replaced
since any parts in the SERVO board cannot be repaired.
NOTE FOR REPLACEMENT OF THE SENSOR BOARD
When the SENSOR board is defective, exchange the MECHANI-
CAL BLOCK (U) ASSY 08 (Former type) or MECHANICAL
BLOCK (11CA) ASSY (New type).
When the SENSOR board is defective, exchange the MECHANI-
CAL BLOCK (U) ASSY 08 (Former type) or MECHANICAL
BLOCK (11CA) ASSY (New type).
Note: As for the mechanism deck (MG-101CA-188) carried in this
unit, component parts have been changed from the midway
of production. When you perform repair exchange of the
mechanism deck (MG-101CA-188), refer to “ABOUT THE
MG-101CA-188 OF FORMER AND NEW” on page 6.
of production. When you perform repair exchange of the
mechanism deck (MG-101CA-188), refer to “ABOUT THE
MG-101CA-188 OF FORMER AND NEW” on page 6.
CLEANING THE CONNECTORS
The unit may not function properly if the connectors
between the unit and the front panel are not clean. In order
to prevent this, detach the front panel and clean the
connectors with a cotton swab. Do not apply too much force.
Otherwise, the connectors may be damaged.
between the unit and the front panel are not clean. In order
to prevent this, detach the front panel and clean the
connectors with a cotton swab. Do not apply too much force.
Otherwise, the connectors may be damaged.
Notes
t For safety, turn off the ignition before cleaning the connectors,
and remove the key from the ignition switch.
t Never touch the connectors directly with your fingers or with
any metal device.
and remove the key from the ignition switch.
t Never touch the connectors directly with your fingers or with
any metal device.
EXTENSION CABLE AND SERVICE POSITION
When repairing or servicing this set, connect the jig cable (extension cable (CD mecha)) as shown below.
When repairing or servicing this set, connect the jig cable (extension cable (CD mecha)) as shown below.
•
Connect the MAIN board (CN700) and the SERVO board (CN401) with the jig cable.
Jig cable:
Part No.
Part No.
Description
A-1818-424-A
EXTENSION CABLE (CD MECHA)
Ver. 1.1
Click on the first or last page to see other CDX-GT560UE / CDX-GT560UI / CDX-GT560US / CDX-GT564UI / CDX-GT610UG / CDX-GT610US / CDX-GT616UG / CDX-GT61UMS service manuals if exist.