HS-MB1 - Sony Audio Service Manual (repair manual). Page 4

Read Sony HS-MB1 Service Manual online

HS-MB1
4
SECTION  2
GENERAL
This section is extracted 
from instruction manual.
Hooking up the HS-MB1
Before hooking up the HS-MB1, be sure the AC power cord is 
unplugged.
Note
If a CAT5 cable is connected to the wrong RJ45 terminal, units or devices 
connected to HS-MB1 may be damaged when you plug in the AC power cord. 
Terminals 
", $, ', and ( supply DC voltage, so make sure of all connections 
before plugging in the AC power cord.
ZONE 1
A
B
ZONE 2
A
B
ZONE 3
A
B
ZONE 4
A
B
ZONE 5
A
B
ZONE 6
A
B
ZONE 7
A
B
ZONE 8
A
B
TO KEYPAD HS-KP1
TO AV WALL PORT HS-WV1
TO COMPONENT VIDEO BALUN CAV-CVB1
TO DIGITAL MEDIA WALL PORT
HS-WD1
OUTPUT
DOOR 2
INPUT
ZONE 1
F
ZONE 2
F
ZONE 3
F
ZONE 4
F
SOURCE 1
E
SOURCE 2
E
SOURCE 3
E
SOURCE 4
E
SOURCE 1
C
D
SOURCE 2
C
D
SOURCE 3
C
D
SOURCE 4
C
D
G
SOURCE DMPORT
H
B
SERVICE
ZONE
LOCAL
MODE
DB2
OFF
2
3
2
E
1
DB1
2
E
1
CHIME
2
E
1
GAIN
1
2
3
DOOR 1
MODE
OFF
2
3
GAIN
1
2
3
 DB1/DB2
Connect the conductor cable for Doorbell.
MODE: Set 2 or 3 depending on the Doorbell manufacturer.
GAIN: Set the mic/speaker level of the Doorbell.
 CHIME
Connect the external chime.
INPUT
 SOURCE 1 ~ 4  
$ %
RJ45 terminals to input audio signal from AV Wall Port(s) 
(HS-WV1).
Use both terminals for the connection.
Note
When you connect a Multi Channel AV Receiver to the HS-MB1, be sure to 
use the SOURCE 1 terminals. The Multi Channel AV Receiver will not work 
with the SOURCE 2, 3, or 4 terminals.
 SOURCE DMPORT  
( )
RJ45 terminals to input Digital Media Port signal from Digital Media 
Wall Port(s) (HS-WD1).
Use both terminals for the connection.
Note
If a DIGITAL MEDIA PORT adapter is connected to a Multi Channel AV 
Receiver which is connected to the HS-MB1, you cannot use the SOURCE 
DMPORT terminals of the HS-MB1.
 DC IN indicator
 SERVICE  
#
RJ45 terminals for Keypad (HS-KP1) firmware updates.
ZONE: Select this when updating the Keypad (HS-KP1) firmware.
LOCAL: Select this when updating this unit’s firmware.
 SOURCE 1 ~ 4  
&
RJ45 terminals to input video signal from AV Wall Port(s) 
(HS-WV1).
OUTPUT
 ZONE 1 ~ 4  '
RJ45 terminals send a video signal source to the component video. 
Use a Component Video Balun (CAV-CVB1) for the connection.
CAT5 RJ45 Pinout
When you connect the Component Video Balun (CAV-CVB1), the 
CAT5 RJ45 pinouts use the T568B standard. Refer to the illustration 
below.
Pinout
Wire color
 Pin 1 BLUE/Pb (R)
White/Orange
 Pin 2 BLUE/Pb (T)
Orange
 Pin 3 GREEN/Y (R) White/Green
 Pin 4 GND
Blue
 Pin 5 +11V
White/Blue
 Pin 6 GREEN/Y (T) Green
 Pin 7 RED/Pr (R)
White/Brown
 Pin 8 RED/Pr (T)
Brown
CAT5 cable
Be sure to use Category 5e straight-through cables, and the wiring 
connection is correct. See the illustration below for details on 
connections.
White/Orange
Wire color
Orange
White/Green
Blue
White/Blue
Green
White/Brown
Brown
1
Pin No.
2
3
4
5
6
7
8
 ZONE 1 ~ 8  " #
RJ45 terminals for Keypad (HS-KP1).
Use both terminals for the connection.
Note
If you use the ZONE 5 ~ 8 terminals, you need to connect the additional 
Power Supply (HS-AC1) (optional) to ZONE 5 – 8 DC IN.
Note on installing CAT5 cables
The following lengths of cable(s) can extend up to 200 feet:
● The combined length of the two longest cables connecting the HS-MB1 to an 
AV Wall Port (HS-WV1) and a Keypad (HS-KP1).
● The combined length of the cable connecting the HS-MB1 to the Digital Media 
Wall Port (HS-WD1) and the longest cable connecting to a Keypad (HS-KP1).
● The length of the longest cable connecting the HS-MB1 to a Component Video 
Balun (CAV-CVB1).
Page of 58
Display

Click on the first or last page to see other HS-MB1 service manuals if exist.