Read Sony CMT-DH888BT / HCD-DH888BT Service Manual online
HCD-DH888BT
4
SECTION 1
SERVICING NOTES
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostat-
ic break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The fl exible board is easily damaged and should be handled with
care.
ic break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The fl exible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused
on the disc refl ective surface by the objective lens in the optical
pickup block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
The laser beam on this model is concentrated so as to be focused
on the disc refl ective surface by the objective lens in the optical
pickup block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong
viscosity
Unleaded solder is more viscous (sticky, less prone to fl ow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
•
Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
also be added to ordinary solder.
RELEASING THE DISC ANTITHEFT
The disc lock function for the antitheft of an demonstration disc in
the store is equipped.
The disc lock function for the antitheft of an demonstration disc in
the store is equipped.
Releasing Procedure :
1. Press the [
1. Press the [
?/1
] button to turn on the system.
2. Press the [DVD
N
] button to select the “DVD”.
3. While pressing the [
x
] button, press the [
Z
] button until
“UNLOCKED” displayed on the fl uorescent indicator tube
(around 5 seconds).
(around 5 seconds).
Note: When “LOCKED” is displayed, the disc lock is not released by
turning power on/off with the
[
?/1
]
button.
NOTE OF REPLACING THE IC103 ON THE DMB15
BOARD
IC103 on the DMB15 board cannot exchange with single. When
this part on the DMB15 board is damaged, exchange the entire
mounted board.
BOARD
IC103 on the DMB15 board cannot exchange with single. When
this part on the DMB15 board is damaged, exchange the entire
mounted board.
Playable discs
Type
Characteristics
Icon used in
this manual
this manual
Logo
DVD VIDEO
DVD VIDEO
DVD-R*/-RW*/+R/+RW
in DVD VIDEO format
* also in video mode
VR mode
DVD-R/-RW
in VR (Video Recording) mode
VIDEO CD
VIDEO CD
Super VCD*
CD-ROM*/-R*/-RW*
* in VIDEO CD or Super VCD format
CD
AUDIO CD*
CD-R*/-RW*
* in AUDIO CD format
DATA CD
CD-ROM/-R/-RW
in DATA CD format, containing
MP3 audio tracks
MP3 audio tracks
1)
, JPEG image
files
2)
or DivX video files
3)
, and
conforming to ISO 9660
4)
Level
1 or Level 2, or Joliet (expansion
format).
format).
Type
Characteristics
Icon used in
this manual
this manual
Logo
DATA DVD
DVD-ROM/-R/-RW/+R/+RW
in DATA DVD format containing
MP3 audio tracks
MP3 audio tracks
1)
, JPEG image
files
2)
or DivX video files
3)
, and
conforming to UDF (Universal Disk
Format).
Format).
This system can also play back discs with the following disc logos:
1)
MP3 (MPEG 1 Audio Layer 3) is a standard format defined by ISO/MPEG which compresses audio
data. MP3 audio tracks must be in MPEG 1 Audio Layer 3 format.
data. MP3 audio tracks must be in MPEG 1 Audio Layer 3 format.
2)
JPEG image files must conform to the DCF image file format. (DCF “Design rule for Camera
File System”: Image standards for digital cameras regulated by Japan Electronics and Information
Technology Industries Association (JEITA)).
File System”: Image standards for digital cameras regulated by Japan Electronics and Information
Technology Industries Association (JEITA)).
3)
DivX video files must be recorded in DivX format with the extension “.AVI” or “.DIVX”.
4)
A logical format of files and folders on CD-ROMs, defined by ISO (International Organization for
Standardization).
Standardization).
“DVD+RW,” “DVD-RW,” “DVD+R,” “DVD VIDEO,” and the “CD” logos are trademarks.
Click on the first or last page to see other CMT-DH888BT / HCD-DH888BT service manuals if exist.