Read Sony BDV-Z7 / SA-WSZ7 / SS-TSZ7 Service Manual online
SA-WSZ7/SS-TSZ7
3
SECTION 1
SERVICING NOTES
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong
viscosity
Unleaded solder is more viscous (sticky, less prone to fl ow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
also be added to ordinary solder.
BEGIN IT BEFORE THE REPAIR (SA-WSZ7)
When the SA-WSZ7 is checked, connect to HCD-Z7 (for Blu-ray
disc/DVD receiver of BDV-Z7). Be sure in advance the HCD-Z7
is prepared.
When the SA-WSZ7 is checked, connect to HCD-Z7 (for Blu-ray
disc/DVD receiver of BDV-Z7). Be sure in advance the HCD-Z7
is prepared.
NOTE OF WHEN OPERATION OF THE SET IS CON-
FIRMED (SA-WSZ7)
This set displays the protector when the fan stops for ten seconds
or more, and operation is stopped.
Do not remove, and stop the fan when you confi rm the operation.
FIRMED (SA-WSZ7)
This set displays the protector when the fan stops for ten seconds
or more, and operation is stopped.
Do not remove, and stop the fan when you confi rm the operation.
NOTE THE IC1165 ON THE AMP-POWER BOARD
REPLACING (SA-WSZ7)
IC1165 on the AMP-POWER board cannot exchange with single.
When this part is damaged, exchange the entire mounted board.
REPLACING (SA-WSZ7)
IC1165 on the AMP-POWER board cannot exchange with single.
When this part is damaged, exchange the entire mounted board.
CAPACITOR ELECTRICAL DISCHARGE PROCESSING
(SA-WSZ7)
When checking the board, for the electric shock prevention, con-
nect the resistors to both ends of respective capacitor (C1009) or
between
(SA-WSZ7)
When checking the board, for the electric shock prevention, con-
nect the resistors to both ends of respective capacitor (C1009) or
between
1 – 2 pins of CN1111 and CN1521 to discharge the
capacitors (C1009, C1105, C1106, C1115, C1426, C1446, C1466).
C1009
CN1111
CN1521
1
1
3
3
800
:/2 W
800
:/2 W
800
:/2 W
– AMP-POWER Board (Conductor Side) –
Click on the first or last page to see other BDV-Z7 / SA-WSZ7 / SS-TSZ7 service manuals if exist.