Read Sony BDV-F500 / BDV-F700 / HBD-F500 / HBD-F700 Service Manual online
HBD-F500/F700
8
MODEL IDENTIFICATION
- Rear view -
- Rear view -
SPEAKERS
FRONT L
SUBWOOFER
FRONT R
Part No.
Model
number
label
number
label
Model
Part No.
HBD-F500: AEP model
4-171-642-0
[]
HBD-F500: UK model
4-171-643-0
[]
HBD-F700: AEP model
4-171-645-0
[]
HBD-F700: UK model
4-171-646-0
[]
HBD-F500: Latin American models
4-174-818-0
[]
NOTE FOR REPLACEMENT OF THE HAMON BOARD
(HBD-F700 only)
When repairing, the complete HAMON board (Part No. A-1751-
874-A) should be replaced since any parts in the HAMON board
cannot be repaired.
(HBD-F700 only)
When repairing, the complete HAMON board (Part No. A-1751-
874-A) should be replaced since any parts in the HAMON board
cannot be repaired.
NOTE OF REPLACING THE IC300 AND IC302 ON
THE AMP BOARD AND THE COMPLETE AMP BOARD
When IC300 and IC302 on the AMP board and the complete AMP
board are replaced, it is necessary to spread the compound (OIL
COMPOUND (G777)) (Part No. J-2501-335-A ) between parts
and heat sink.
Spread the compound referring to the fi gure below.
THE AMP BOARD AND THE COMPLETE AMP BOARD
When IC300 and IC302 on the AMP board and the complete AMP
board are replaced, it is necessary to spread the compound (OIL
COMPOUND (G777)) (Part No. J-2501-335-A ) between parts
and heat sink.
Spread the compound referring to the fi gure below.
– AMP Board (Component Side) –
IC300
IC302
IC302
IC300
NOTE WHEN VOLTAGE ON THE AMP BOARD IS
MEASURED
Do the following work when you measure the voltage of the AMP
board.
MEASURED
Do the following work when you measure the voltage of the AMP
board.
Procedure:
1. Remove the FAN motor (M301, 302).
2. Be short-circuited of SL192 on the AMP board.
1. Remove the FAN motor (M301, 302).
2. Be short-circuited of SL192 on the AMP board.
– AMP Board (Component Side) –
SL192
SL192
IC101
Note: The set enters the state of protect when SL192 is not short-circuited.
Moreover, the set enters the state of protecting when the motor is
not detached with SL192 short-circuited.
not detached with SL192 short-circuited.
3. Measure the voltage of the AMP board.
4. Remove solder on SL192 after the measurement ends.
5. Assemble the FAN motor (M301, 302).
4. Remove solder on SL192 after the measurement ends.
5. Assemble the FAN motor (M301, 302).
NOTE OF DISC PLAYBACK IN DISASSEMBLED STATE
Reproduce by setting up the BD drive without fail in the vertical
direction (the same direction as the state of the set) when you re-
produce the disc with the set taken apart.
There is a possibility that the disc is not correctly reproduced when
setting it up in a wrong direction (horizontal direction etc.).
Reproduce by setting up the BD drive without fail in the vertical
direction (the same direction as the state of the set) when you re-
produce the disc with the set taken apart.
There is a possibility that the disc is not correctly reproduced when
setting it up in a wrong direction (horizontal direction etc.).
OK
NG
Click on the first or last page to see other BDV-F500 / BDV-F700 / HBD-F500 / HBD-F700 service manuals if exist.