Read Sharp AR-M700 (serv.man31) Service Manual online
: Feb. 9 2004
1
AR-M550/M620/M700 OTHER 12 - 1
[12] OTHER
1. VARIOUS COUNTERS SPECIFICATIONS]
A. Count specification
(1) Paper exit system counter
Large size: A3, 11 x 17. (Greater size than paper length 384mm)
∗
( ): Count-up number when setting to the large size single count up.
(2) Document, finishing, paper feed system counter
Counter
Count-up timing
Count-up number
Counter
reset
procedure,
clear
Simplex copy
Duplex copy
Paper feed tray – Main
unit paper exit
Paper feed tray – ADU
ADU – Main unit paper
exit
Small size Large size Small size Large size Small size Large size
Total counter (Note)
When transfer is completed
1
2 (1)
1
2 (1)
1
2 (1)
—
Maintenance counter
When transfer is completed
1
2 (1)
1
2 (1)
1
2 (1)
Sim24-4
Developer counter
When transfer is completed
1
2 (1)
1
2 (1)
1
2 (1)
Sim24-5
All valid paper counter (Note)
When paper exit
1
2 (1)
—
—
2
4 (2)
—
Copy counter (Copy valid paper) When paper exit
1
2 (1)
—
—
2
4 (2)
Sim24-6
FAX counter
When paper exit
1
2 (1)
—
—
2
4 (2)
Sim24-10
Print counter
When paper exit
1
2 (1)
—
—
2
4 (2)
Sim24-9
Internet FAX counter
When paper exit
1
2 (1)
—
—
2
4 (2)
Sim24-15
Document filing counter
When paper exit
1
2 (1)
—
—
2
4 (2)
Sim24-15
Right side paper exit counter
When center paper exit
1
2 (1)
—
—
2
4 (2)
—
Other counter (Self print, etc.)
When paper exit
1
2 (1)
—
—
2
4 (2)
Sim24-9
Counter
Mode
Count event
Count-up condition
Counter reset
procedure,
clear
SPF counter
All modes
SPF paper
feed number
feed number
Count is made when starting SPF paper pick.
Sim24-3
Finish stamp counter
FAX send
Internet FAX send
Internet FAX send
Finish stamp
use number
use number
Count is made when stamp is ON.
Sim24-3
Staple counter
All modes
(Including inserter
stand alone process)
(Including inserter
stand alone process)
Staple
number
number
Count is made when bundle exit process is completed.
Double count is made when stapling two positions.
In the inserter stand alone mode, count is made when process is
completed.
Double count is made when stapling two positions.
In the inserter stand alone mode, count is made when process is
completed.
Sim24-3
Punch counter
All modes
(Including inserter
stand alone process)
(Including inserter
stand alone process)
Punch
number
number
Count is made when bundle exit process is completed.
1 count regardless of the kind of the punch unit (2-hole, 3-hole, etc.)
In the inserter stand alone mode, count is made when process is
completed.
1 count regardless of the kind of the punch unit (2-hole, 3-hole, etc.)
In the inserter stand alone mode, count is made when process is
completed.
Sim24-3
Saddle staple counter
All modes
(Including inserter
stand alone process)
(Including inserter
stand alone process)
Saddle
staple
number
staple
number
Count is made when bundle paper exit process is c completed.
Only one count is added.
In the inserter stand alone mode, count is made when process is
completed.
Only one count is added.
In the inserter stand alone mode, count is made when process is
completed.
Sim24-3
Scan total counter
All modes
Scan
number
number
Count is made when scan is completed.
Sim24-3
ADU counter
All modes
ADU paper
feed number
feed number
Count is made when paper feed from the ADU section is started.
Sim24-2
Inserter counter
All modes
(Including inserter
offline process)
(Including inserter
offline process)
Inserter tray
paper feed
number
paper feed
number
Count is made when paper feed from the inserter tray is started.
In the inserter stand alone mode, count is made when process is
completed.
In the inserter stand alone mode, count is made when process is
completed.
Sim24-3
Paper
feed
counter
feed
counter
Manual paper
feed tray
feed tray
All modes
Tray paper
feed number
feed number
Count is made when paper feed from each tray is started.
Sim24-2
Paper feed tray 1
Sim24-2
Paper feed tray 2
Sim24-2
Paper feed tray 3
Sim24-2
Paper feed tray 4
Sim24-2
LCC
Sim24-2
: Feb. 9 2004
1
AR-M550/M620/M700 OTHER 12 - 2
(3) Send system counter
Counter
Mode
Count event
Count-up condition
Counter reset
procedure,
clear
Accumulated
number of FAX
send
number of FAX
send
G3 FAX send
Number of send
Except for the serial transmit operation, one reservation is counted as
one communication.
For the serial transmit operation, count is made for each
communication individually.
Recall is not included.
Polling is counted as a number of send.
one communication.
For the serial transmit operation, count is made for each
communication individually.
Recall is not included.
Polling is counted as a number of send.
Sim24-10
Accumulated
page number of
FAX send
page number of
FAX send
G3 FAX send
Total page number of
send
send
In the serial transmit operation, each communication is counted as one
individually.
In bulletin board send, the page number of send is counted.
individually.
In bulletin board send, the page number of send is counted.
Sim24-10
Accumulated
time of FAX send
time of FAX send
G3 FAX send
Send time
(Including resending
time.)
(Including resending
time.)
Sim24-10
Accumulated
page number of
scanner scan
page number of
scanner scan
Scan to E-mail send
SHARP DESK send
FTP send
SHARP DESK send
FTP send
Page number of scan Even in the serial transmit operation, the page number of one scan is
counted.
(The number of receivers is not counted.)
In case of a send error (excluding document jam)
• E-mail
(The number of receivers is not counted.)
In case of a send error (excluding document jam)
→
Not counted.
• SHARP DESK/FTP
→
Counted.
Sim24-15
Accumulated
number of mail
send
number of mail
send
Scan to E-mail send Number of mails
reached to
destination servers
destination servers
Even in the serial transmit operation, the page number of one scan is
counted.
(The number of receivers is not counted.)
Cancel and network error are not counted.
counted.
(The number of receivers is not counted.)
Cancel and network error are not counted.
Sim24-15
Accumulated
number of FTP
send
number of FTP
send
SHARP DESK send
FTP send
FTP send
Number of send
reached to
destination servers
reached to
destination servers
Mails transmitted by FTP send are counted in the accumulated
number of mail send.
Even in the serial transmit operation, the page number of one scan is
counted.
(The number of receivers is not counted.)
Cancel and network error are also counted.
number of mail send.
Even in the serial transmit operation, the page number of one scan is
counted.
(The number of receivers is not counted.)
Cancel and network error are also counted.
Sim24-15
Accumulated
number of
internet FAX
send
number of
internet FAX
send
Internet FAX send
Page number of send Even in the serial transmit operation, the page number of one scan is
counted.
(The number of receivers is not counted.)
The final send result is counted.
A send error is counted.
Resend is not counted.
Cancel and CE error are not counted.
(The number of receivers is not counted.)
The final send result is counted.
A send error is counted.
Resend is not counted.
Cancel and CE error are not counted.
Sim24-15
Accumulated
number of
internet FAX
receive
number of
internet FAX
receive
Internet FAX send
Page number of scan Even in the serial transmit operation, the page number of one scan is
counted.
(The number of receivers is not counted.)
The final send result is counted.
A communication error (except for document jam) is counted.
Cancel and CE error are not counted.
A send (transfer, F code relay broadcast) without document scan is not
counted.
(The number of receivers is not counted.)
The final send result is counted.
A communication error (except for document jam) is counted.
Cancel and CE error are not counted.
A send (transfer, F code relay broadcast) without document scan is not
counted.
Sim24-15
Scanner trial
counter
counter
Internet FAX send
Scan to E-mail send
SHARP DESK send
FTP send
Scan to E-mail send
SHARP DESK send
FTP send
Page number of scan Count is made for every scan of page.
Count is made even when send is not completed.
The operation is terminated when the count number exceeds 500.
The operation is terminated when the count number exceeds 500.
—
Page number of
Scan to HDD
Scan to HDD
When reading
SCAN TO HDD
SCAN TO HDD
HDD storage page
number
number
Sim24-15
: Feb. 9 2004
1
AR-M550/M620/M700 OTHER 12 - 3
(4) Receive system counter
(5) Department counter
(6) Printer job count-up specification
* When there is “NO” in account administration, or when there is not “NO.”
Counter
Mode
Count event
Count-up condition
Counter reset
procedure,
clear
The accumulated
page number of
FAX receive print
page number of
FAX receive print
G3 FAX
receive
receive
Total output
page number
page number
The FAX separator sheet is also counted.
When polling, the number of received pages is counted.
Count by size and count in recovery are the same as the copier specifications.
(Counted by the print system.)
When polling, the number of received pages is counted.
Count by size and count in recovery are the same as the copier specifications.
(Counted by the print system.)
Sim24-10
Accumulated time
of FAX receive
of FAX receive
G3 FAX
receive
receive
Receive time
Sim24-10
Accumulated
number of internet
FAX receive
number of internet
FAX receive
Internet
FAX receive
FAX receive
Receive
number
number
A normal mail receive is also counted.
Count is made regardless of normal or abnormal.
Count is made regardless of print result.
Count is made regardless of normal or abnormal.
Count is made regardless of print result.
Sim24-15
Accumulated page
number of internet
FAX receive print
number of internet
FAX receive print
Internet
FAX receive
FAX receive
Total receive
output number
output number
Count is made when output is made on a normal mail receive.
Print of mail text is not counted.
The FAX separator sheet is also counted.
Count by size and count in recovery are the same as the copier specifications.
(Counted by the print system.)
Print of mail text is not counted.
The FAX separator sheet is also counted.
Count by size and count in recovery are the same as the copier specifications.
(Counted by the print system.)
Sim24-15
Operation content
Data location
Conforming count mode
(SIM 26-5)
Count-up condition
MFP
Control
PWB
FAX
Scanner
control
PWB
PCU
PWB
TOTAL
Mainte-
nance
DV
Copy counter
●
■
Print counter
●
■
FAX send page
number counter
number counter
●
■
Department FAX send page number
• In the serial transmit operation, each communication is
• In the serial transmit operation, each communication is
counted as one individually.
Network scanner
counter
counter
●
—
—
—
Department network scanner scan page number
• iFAX and network scanner
• Even in the serial transmit operation, the page number of
• iFAX and network scanner
• Even in the serial transmit operation, the page number of
one scan is counted. (The number of receivers is not
counted.)
counted.)
I-FAX send page
number counter
number counter
●
■
Department FAX send page number
• In the serial transmit operation, each communication is
• In the serial transmit operation, each communication is
counted as one individually.
Document filing
●
■
Total use page number
counter
Department counter
PRINTS
OTHERS
Key operation
number
Driver specification
account number
Other department
(OTHERS)
Printer job (Without account administration)
❍
—
—
—
—
Printer job (With account specification) *
❍
—
—
❍
—
Printer job (Without account specification) *
❍
—
—
—
❍
Notice in printer job (Without account administration)
❍
—
—
—
—
Notice in printer job (With account specification) *
❍
—
—
—
❍
Notice in printer job (Without account specification) *
❍
—
—
—
❍
List print
—
❍
—
—
—
Total use page number print
—
❍
—
—
—
Each department total page number print
—
❍
—
—
—
Engine self print
—
—
—
—
—
: Feb. 9 2004
1
AR-M550/M620/M700 OTHER 12 - 4
(7) Total counter specifications
The total count viewed from the user and the counter used for charging are “Total output counter (total valid paper counter).”
(8) Blank paper count specification
∗
Large size: A3, 11 x 17. (Greater size than paper length 384mm)
*1: Follows SIM 26-5 (Count-up mode). (Default: Double count-up (Set value: 2))
( ): Large size single count-up setting (Count-up number when set to 1.)
❍
: Counts up.
✕
: Does not count up.
∆
:
Follows SIM 26-52 setting.
0: Does not count up. (Japan/SCA default)
1: Counts up. (Other default)
—: Out of target (No print process)
(9) Consumables counter specification
Total output counter (Total valid paper counter)
Total counter
Display when the copy key is ON.
■
—
List print
■
—
Valid paper counter to send to serial RIC
■
—
Total counter to send to serial RIC
■
—
E-RIC mail text counter
■
—
E-RIC attached file
■
(Counter for the first send)
■
(Counter to send in the midst of packet)
SIMULATION
Displayed/printed as Total output.
Displayed/printed as Total
1
Mode
Print mode
Count attribute
Blank paper count setting (SIM 26-52)
Remark
Print surface
0: NO
1: YES
Front
surface
Back
surface
Small
size
Large
size
Small
size
Large
size
Normal Without print (Invalid paper exit)
✕
—
0
0
0
0
Without print (Blank paper
insertion)
insertion)
∆
—
0
0
1
2 (1) *1
Single face print (Single face mode)
❍
—
1
2 (1) *1
1
2 (1) *1
SS/DS
Single face print (Duplex mode)
❍
✕
1
2 (1) *1
1
2 (1) *1
SD (Odd number of documents)
Duplex print
❍
❍
2
4 (2) *1
2
4 (2) *1
SD (Even number of documents)/
DD
DD
Front
cover
cover
Without print
∆
—
0
0
1
2 (1) *1
With print (Single face)
❍
—
1
2 (1) *1
1
2 (1) *1
With print (Duplex)
❍
❍
2
4 (2) *1
2
4 (2) *1
Back
cover
cover
Without print
✕
∆
0
0
1
2 (1) *1
With print (Single face)
✕
❍
1
2 (1) *1
1
2 (1) *1
With print (Duplex)
❍
❍
2
4 (2) *1
2
4 (2) *1
Insert
paper
paper
Without print
∆
—
0
0
1
2 (1) *1
With print (Single face)
❍
—
1
2 (1) *1
1
2 (1) *1
With print (Duplex)
❍
❍
2
4 (2) *1
2
4 (2) *1
OHP
insert
paper
insert
paper
Without print
∆
—
0
0
1
2 (1) *1
With print (Single face)
❍
—
1
2 (1) *1
1
2 (1) *1
With print (Duplex)
—
—
—
—
—
—
Duplex print inhibition
Counter
Count-up timing
Count-up number
Counter
reset
procedure,
clear
Simplex print
Duplex print
Paper feed tray –
Main unit paper exit
Paper feed tray –
ADU
ADU – Main unit
paper exit
Small size Large size Small size Large size Small size Large size
OPC drum counter
When transfer is completed
1
2 (1)
1
2 (1)
1
2 (1)
Sim24-7
OPC drum rotation counter (sec)
When transfer is completed
—
—
—
—
—
—
Sim24-11
Developer counter
When transfer is completed
1
2 (1)
1
2 (1)
1
2 (1)
Sim24-5
Developing roller rotation counter
(sec)
(sec)
When transfer is completed
—
—
—
—
—
—
Sim24-11
Toner counter
When transfer is completed
1
2 (1)
1
2 (1)
1
2 (1)
—
Toner supply counter (sec)
When transfer is completed
—
—
—
—
—
—
—