AR-C262M (serv.man3). Service Manual - Sharp Copying Equipment Service Manual (repair manual). Page 16

AR-C262M  SPECIFICATIONS  3 - 7

The scanner function is enabled by canceling the product key in
the MFP model. This function also requires installation of 256MB
expansion memory.

PUSH SCAN is used to send scan data to PC or a file server by
the operation on the machine operation panel.

PUSH SCAN has the following three modes:

• SCAN TO E-MAIL (SMTP) 

Scan data area attached to an E-mail.

• SCAN TO FILE SERVER (FTP)

Scan data are sent to a file server by FTP.

The URL can be e-mailed simultaneously.

• SCAN TO DESKTOP (FTP)

Scan data are sent to the desktop user. (SHARPDESK and the
network scanner tool are required.)

1. Push [IMAGE SEND] button on the operation panel to switch to

the main menu of the image send mode.

2. Press [ADDRESS DIRECTORY] or [E-MAIL ADDRESS] button

to set a destination. (The local address book cannot be
retrieved.)

3. According to the necessity, set the sender with [SENDER LIST]

button.

4. According to necessity, select the scanning conditions with

[EXPOSURE], [RESOLUTION], [FORMAT] and [ORIGINAL]
buttons.

5. Press the color start key or the black-and-white start key to

start scanning. When the color start key is pressed, scanning is
made in color. When the black-and-white start key is pressed,
scanning is made in black and white.
Engine operates according to the setting made, such as: LED
of the color start key is turned on or LED of mono start key is
turned on.

Network protocol

TCP/IP, SMTP, FTP, (HTTP)

Trial mode

Supported by the service diag.
The upper limit is 500 scans (surfaces). Without canceling the product key, scanning functions are enabled.
500 counts in total of color and black-and-white scans. No counter for the trial mode.
Resolution level: [lowest] or [lower] key only.

Destination registration 500 items of scan to E-mail from Embedded Web Server + group, and 100itmes of Scan to FTP + Desktop (Max. 

600 items can be registered.)
Scan to E-mail and group can be registered from the operation panel.
A destination name can be set with max. 18 characters in two bytes (or 36 characters in one byte).
An E-mail address can beg set with max. 50 characters in one byte.

Address book

The static address book stored in MFP is supported.

Destination select

Selected from the operation panel.
Selection of two or more destinations is allowed. (Only Scan to E-mail)
Transmission to temporary user is available.
CC: / BCC: Send enable

Sender select

Selected from the senders (20) registration list by the key operation on the operation panel.
If it is not set, the default registered on the Web is used.
Setting can be made with the key operator program.

Image setup

Image quality setup

Color (RGB, each 8bit), Monochrome binary (1bit)

Binary system

Error diffusion 

Text/photo area separation Automatic

Moire reduction mode

Yes

Color enhancement mode

N/A

Density

Automatic (Monochrome only. For color, same as density 3 manual.)
Manual (9 steps: 1 to 5, 0.5 increment)
Default: 3

Resolution

Color

Monochrome

Low 2

100dpi

150dpi

Low 1

150dpi

200dpi (Default)

Normal

200dpi

300dpi

High 1

300dpi

400dpi

High 2

600dpi

600dpi

The above resolutions are displayed on the panel. 
There is no optional setting of resolution. 

Document

Document arrangement

Single surface document
Duplex document (side bind)
Duplex document (top bind)

Image rotation 

0°
90° (A document is rotated 90 degrees to be set. Used mainly for portrait image scan 
of Legal, B4, A3. etc.)
Note: 600 x 600dpi A3 size full color scan: 90-degree image rotate every time.

Document detection size

Automatic detection (The automatic detection allowable size can be set by the key 
operation.)
Manual setup (Automatic detection cancel: Fixed sizes)
Manual setup (Automatic detection cancel: Other than fixed sizes)
AB series: mm setting,  inch series: inch setting