Read Panasonic HDC-SD40P / HDC-SD40PC / HDC-SD40PU / HDC-SD40EB / HDC-SD40EC / HDC-SD40EE / HDC-SD40EF / HDC-SD40EG / HDC-SD40EP / HDC-SD40GA / HDC-SD40GC / HDC-SD40GK / HDC-SD40GN / HDC-SD40GW / HDC-SD41EB / HDC-TM40P / HDC-TM40PC / HDC-TM40PU / HDC-TM40EB / HDC-TM40GD Service Manual online
HDC-SD40PC
HDC-SD40PU
HDC-SD40EB
HDC-SD40EC
HDC-SD40EE
HDC-SD40EF
HDC-SD40EG
HDC-SD40EP
HDC-SD40GA
HDC-SD40GC
HDC-SD40GK
HDC-SD40GN
HDC-SD40GW
HDC-SD41EB
HDC-TM40P
HDC-TM40PC
HDC-TM40PU
HDC-TM40EB
HDC-TM40GD
HDC-TM40GK
HDC-TM41P
[HDC-SD40]
(K)...........Black Type
(W)..........White Type (only EB/EC/EE/EF/EG/EP)
(H)...........Glay Type
(K)...........Black Type
(H)...........Glay Type
1.2. Leakage Current Cold Check ---------------------------3
1.3. Leakage Current Hot Check (See Figure 1.) --------3
2.4. How to Replace the Lithium Battery -------------------6
3.2. General Description About Lead Free Solder
3.4. How to Define the Model Suffix (NTSC or PAL
5 Location of Controls and Components------------------ 12
6 Service Fixture & Tools --------------------------------------- 14
6.2. Service Position ------------------------------------------ 14
7.2. PCB Location---------------------------------------------- 15
7.3. Disassembly Procedure -------------------------------- 15
9.2. What Is The Factory Settings? ----------------------- 24
which are important for safety. These parts are marked by
tial that these critical parts should be replaced with manu-
facturer’s specified parts to prevent X-RADIATION,
shock, fire, or other hazards. Do not modify the original
design without permission of manufacturer.
from the AC power line. Use a transformer of adequate
power rating as this protects the technician from acci-
dents resulting in personal injury from electrical shocks. It
will also protect AC Adaptor from being damaged by acci-
dental shorting that may occur during servicing.
heated or damaged by the short circuit.
properly installed.
shock hazards.
lic cabinet part on the equipment such as screwheads,
connectors, control shafts, etc. When the exposed metal-
lic part has a return path to the chassis, the reading
should be between 1 M
reading must be infinity.
(See Figure 1.)
and a good earth ground, as shown in Figure 1.
lent) may be used to make the hot checks, leakage cur-
rent must not exceed 1/2 mA. In case a measurement is
outside of the limits specified, there is a possibility of a
shock hazard, and the equipment should be repaired and
rechecked before it is returned to the customer.
Sensitive (ES) Devices
trostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and
semiconductor "chip" components. The following techniques should be used to help reduce the incidence of component damage
caused by electrostatic discharge (ESD).
which should be removed for potential shock reasons prior to applying power to the unit under test.
4. Use only an antistatic solder removal device. Some solder removal devices not classified as "antistatic (ESD protected)" can
6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most
ble conductive material).
CAUTION :
ficient to damage an ES device).