Read JBL CS200.1 Service Manual online
CS Series
200.1
1 CHANNEL POWER AMPLIFIER
SERVICE MANUAL
JBL Consumer Products
250 Crossways Park Dr.
250 Crossways Park Dr.
Woodbury, New York 11797 Rev0
3/2004
- CONTENTS -
SPECIFICATIONS ………………………………….……..1
CONNECTIONS………………….……...……..…...…..…2
CONNECTIONS………………….……...……..…...…..…2
CONTROLS ……..…………………..….…...…….….…...3
BASIC TROUBLESHOOTING..…….…….………………3
EXPLODED VIEW/PARTS LIST…….….….…………....4
BASIC TROUBLESHOOTING..…….…….………………3
EXPLODED VIEW/PARTS LIST…….….….…………....4
AMPLIFIER BLOCK DIAGRAM…………………….……5
P.C.B. DRAWINGS….……………………………….…….6
ELECTRICAL PARTS LIST ..…………………………....8
P.C.B. DRAWINGS….……………………………….…….6
ELECTRICAL PARTS LIST ..…………………………....8
IC/TRANSISTOR PINOUTS..……..….…….….….….….11
SCHEMATICS………..……………………….…………..12
PACKING……..……………………………….….….…...15
SCHEMATICS………..……………………….…………..12
PACKING……..……………………………….….….…...15
CS200.1 Specifications
Output Power:
236W RMS x 1 channel @ 4 ohms, ≤1% THD + N
(14.4V supply)
338W RMS x 1 channel @ 2 ohms, ≤1% THD + N
Signal-to-noise ratio:
100dBA (reference 1W into 4 ohms)
Dynamic power:
464W @ 2 ohms
Effective damping factor:
6.395 @ 4 ohms
Frequency response:
10Hz – 320Hz (–3dB)
Maximum input signal:
7.5V
Maximum sensitivity:
260mV
Bass boost (45Hz)
Variable 0 – 6dB
DC
Offset
<30mV
Output regulation:
.073dB @ 4 ohms
Idle
Current
0.71A
Input Impedance
20kΩ
Max Current Draw
23A @ 4 ohms
42A
@
2
ohms
Dimensions:
12 x 10 x 2 1/4”
(L x W x H)
(305mm
x
254mm
x
57mm)
Fuses:
20A
x
2
JBL continually strives to update and improve existing products, as well as create new ones. The specifications and
details in this and related JBL publications are therefore subject to change without notice.
1
APPLICATIONS – CS200.1
The CS subwoofer amplifier is a
single-channel amplifier. There are
two sets of terminals to make it easy
to connect multiple woofers. Either
set of (+/–) terminals may be used
when connecting woofers.
single-channel amplifier. There are
two sets of terminals to make it easy
to connect multiple woofers. Either
set of (+/–) terminals may be used
when connecting woofers.
To the right are two application
diagrams to help plan your subwoofer
system installation. Figures 2 and 3
show how to configure the CS200.1
subwoofer amplifier.
diagrams to help plan your subwoofer
system installation. Figures 2 and 3
show how to configure the CS200.1
subwoofer amplifier.
NOTE: For simplicity, Figures 2 and 3
do not show power, remote and input
connections.
do not show power, remote and input
connections.
NOTE: Minimum speaker load is
2 ohms total.
2 ohms total.
Figure 2. CS subwoofer amplifier with two woofers
connected.
connected.
Figure 3. CS subwoofer amplifier with one woofer
connected.
connected.
Figure 4. CS50.4 amplifier in 4-channel (stereo)
operation to drive front and rear full-range speakers.
operation to drive front and rear full-range speakers.
Figure 5. CS50.4 is set up for 3-channel operation to
drive a set of full-range speakers and a subwoofer.
drive a set of full-range speakers and a subwoofer.
Figure 6. CS50.4 used in bridged 2-channel mode
to drive a set of components or subwoofers. Set
crossovers according to application.
to drive a set of components or subwoofers. Set
crossovers according to application.
APPLICATIONS – CS50.4
The CS50.4 can be set up for stereo
4-channel, 3-channel or bridged
2-channel operation, as shown in
Figures 4 through 6.
4-channel, 3-channel or bridged
2-channel operation, as shown in
Figures 4 through 6.
NOTE: For simplicity, Figures 4 through
6 do not show power, remote and input
connections.
6 do not show power, remote and input
connections.
NOTE: Minimum speaker impedance
for stereo operation is 2 ohms.
Minimum speaker impedance for
bridged operation is 4 ohms.
for stereo operation is 2 ohms.
Minimum speaker impedance for
bridged operation is 4 ohms.
CS Series 200.1
2
Features, specifications and appearance are subject to change without notice.
CONTROLS AND SETUP
SYMPTOM
LIKELY CAUSE
SOLUTION
No audio
No voltage at BATT+
Check voltages at
(POWER LEDs
or REM terminals,
amplifier terminals
are off)
or bad or no ground
with VOM
connection
No audio
Amplifier is
Make sure amplifier
(POWER
overheated
cooling is not blocked
LEDs are on)
at mounting location;
verify speaker-system
impedance is within
specified limits
verify speaker-system
impedance is within
specified limits
Voltage more than 16V
Check vehicle
or less than 8.5V on
charging system
BATT+ connection
SYMPTOM
LIKELY CAUSE
SOLUTION
No audio
Voltage less than 9V on
Check vehicle
(POWER BATT+
connection
charging
system
LEDs flash)
DC voltage on
Amplifier may need
amplifier output
service; see enclosed
warranty card for
service information
warranty card for
service information
Distorted audio
Input sensitivity is
Check INPUT
not set properly, or
LEVEL setting; or
amplifier or source
check speaker wires
unit is defective
for shorts or grounds
Distorted audio
Short circuit in
Remove speaker leads
and POWER
speaker or wire
one at a time to locate
LEDs flash
shorted speaker or
wire, then repair
wire, then repair
Music lacks
Speakers are not
Check speaker
“punch”
connected properly
connections for
proper polarity
proper polarity
SETTING THE
CROSSOVER(S)
Determine your system plans and set
the crossover mode switch accordingly.
If your system design does not include
a subwoofer with the CS50.4, set the
crossover mode to FLAT and skip to
“Setting Input Sensitivity.”
CROSSOVER(S)
Determine your system plans and set
the crossover mode switch accordingly.
If your system design does not include
a subwoofer with the CS50.4, set the
crossover mode to FLAT and skip to
“Setting Input Sensitivity.”
Initially set the crossover frequency
control midway. While listening to music,
adjust the crossover for the least
perceived distortion from the speakers,
allowing them to reproduce as much
bass as possible.
control midway. While listening to music,
adjust the crossover for the least
perceived distortion from the speakers,
allowing them to reproduce as much
bass as possible.
Systems using a separate subwoofer set
the crossover mode to HP (high pass) for
your full-range speakers. Adjust the
crossover frequency to limit bass and
provide increased system volume with
less distortion.
the crossover mode to HP (high pass) for
your full-range speakers. Adjust the
crossover frequency to limit bass and
provide increased system volume with
less distortion.
For subwoofers, choose the highest
frequency that removes vocal information
from the sound of the subwoofer.
frequency that removes vocal information
from the sound of the subwoofer.
If using the CS50.4 to drive a subwoofer(s),
set the crossover mode to LP (low pass).
set the crossover mode to LP (low pass).
SETTING INPUT
SENSITIVITY
1. Initially turn the INPUT LEVEL control(s)
SENSITIVITY
1. Initially turn the INPUT LEVEL control(s)
to minimum (counter clockwise).
2. Reconnect the (–) negative lead to the
vehicle’s battery. Apply power to the
audio system and play a dynamic music
track.
audio system and play a dynamic music
track.
3. On the source unit, increase the volume
control to 3/4 volume. Slowly increase
the INPUT LEVEL control(s) toward three
o’clock until you hear slight distortion
in the music. Then reduce the INPUT
LEVEL slightly until distortion is no
longer heard.
the INPUT LEVEL control(s) toward three
o’clock until you hear slight distortion
in the music. Then reduce the INPUT
LEVEL slightly until distortion is no
longer heard.
NOTE: After the source unit is on, blue
LEDs (on the top panel) will light, indicating
the amplifier is on. If not, check the wiring,
especially the remote connection from the
source unit. Also refer to “Troubleshooting”
guide below.
LEDs (on the top panel) will light, indicating
the amplifier is on. If not, check the wiring,
especially the remote connection from the
source unit. Also refer to “Troubleshooting”
guide below.
TROUBLESHOOTING
www.jbl.com
CS Series 200.1
3