Read Harman Kardon AVR 245 (serv.man3) EMC - CB Certificate online
- Page 8 of 8 -
www.nemko.com
Report No. 73226
14.3.3
Transformer/motor, constructional requirements
P
Transformer Insulation Insulation
Res.
Test Volt
Clearances / Creepage distances
Part No.
Between
M Ohms
kV (60 sec.)
Measured
Required
KLT5W026ZE, or
Pr - sec
> 100
3KV (rms)
10,5 / 10,5mm
4,0 / 5,6 mm
CLT5W026ZE
Pr - ic
> 100
3KV (rms)
10,5 / 10,5mm
4,0 / 5,0 mm
KLT5J033YE, or
Pr – sec
> 100
3KV (rms)
7,5 / 7,5 mm
4,0 / 5,0 mm
CLT5J033YE
Pr - ic
> 100
3KV (rms)
6,5 / 6,5 mm
4,0 / 5,0 mm
-
Components / construction
(
(
KLT5W026ZE or CLT5W026ZE)
Windings on two separate bobbins. The
bobbins are placed in an insulating housing with
two compartments, one above the other.
Bobbin thickness: > 0,4mm.
Max. Working voltage: 381Vp/269Vrms
bobbins are placed in an insulating housing with
two compartments, one above the other.
Bobbin thickness: > 0,4mm.
Max. Working voltage: 381Vp/269Vrms
P
Components / construction
(
(
KLT5J033YE or CLT5J033YE)
Windings on single bobbin. The center flange
provided between primary and secondary
windings. Satisfactory constructed.
Bobbin thickness: > 0,4mm.
Max. Working voltage: 344Vp/243Vrms
provided between primary and secondary
windings. Satisfactory constructed.
Bobbin thickness: > 0,4mm.
Max. Working voltage: 344Vp/243Vrms
P
Transformer Insulation
Thick
(mm)
Material
Dielectric strength test
Part No.
Between
X Number
60 sec.
KLT5W026ZE, or Pr - sec
0,75 mm min. x 1
PET bobbin
1 layer tested – Pass *)
CLT5W026ZE
Pr - ic
0,75 mm min. x 1
PET bobbin
1 layer tested – Pass *)
KLT5J033YE, or
CLT5J033YE
CLT5J033YE
Pr - sec
0,50 mm min. x 2
0,50 mm min. x 1
0,50 mm min. x 1
PET bobbin wall
PBT bobbin cap.
PBT bobbin cap.
1 layer tested – Pass *)
Pr - ic
0,60 mm min. x 1
PET bobbin
1 layer tested – Pass *)
Pr - ic
0,50 mm min. x 1
PBT bobbin cap.
1 layer tested – Pass *)
*) Test voltage: 3000 Vrms
17.1
Torque test to Table 20:
P
Screw
Diameter
With
Without
Material
Torque test (Nm)
Location / function
(mm)
Head
Head
Screw
Nut
Fulfilled / Remarks
Fixing of top cover
(sides)
(sides)
4,0 x -
Metal
Metal
Tested with 1,2Nm,
5 times / Pass
5 times / Pass
Fixing of top cover
(rear)
(rear)
3,0 x -
Metal
Metal
Tested with 0,5Nm,
5 times / Pass
5 times / Pass